/* u8x8_d_ssd1306_72x40.c Universal 8bit Graphics Library (https://github.com/olikraus/u8g2/) Copyright (c) 2019, olikraus@gmail.com All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include "u8x8.h" /* EastRising 0.41 OLED https://www.buydisplay.com/default/white-0-42-inch-oled-display-panel-72x40-iic-i2c-serial-spi-ssd1306 command(0xae);//--turn off oled panel command(0xd5);//--set display clock divide ratio/oscillator frequency command(0x80);//--set divide ratio command(0xa8);//--set multiplex ratio command(0x27);//--1/40 duty command(0xd3);//-set display offset command(0x00);//-not offset command(0xad);//--Internal IREF Setting command(0x30);//-- command(0x8d);//--set Charge Pump enable/disable command(0x14);//--set(0x10) disable command(0x40);//--set start line address command(0xa6);//--set normal display command(0xa4);//Disable Entire Display On command(0xa1);//--set segment re-map 128 to 0 command(0xC8);//--Set COM Output Scan Direction 64 to 0 command(0xda);//--set com pins hardware configuration command(0x12); command(0x81);//--set contrast control register command(0xaf); command(0xd9);//--set pre-charge period command(0x22); command(0xdb);//--set vcomh command(0x20); command(0xaf);//--turn on oled panel */ static const uint8_t u8x8_d_ssd1306_72x40_er_init_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C(0x0ae), /* display off */ U8X8_CA(0x0d5, 0x080), /* clock divide ratio (0x00=1) and oscillator frequency (0x8) */ U8X8_CA(0x0a8, 0x027), /* multiplex ratio, 0.42 OLED: 0x27*/ U8X8_CA(0x0d3, 0x000), /* display offset, 0.42 OLED */ U8X8_CA(0x0ad, 0x030), /* Internal IREF Setting for the 0.42 OLED, see also issue https://github.com/olikraus/u8g2/issues/1047 */ U8X8_CA(0x08d, 0x014), /* [2] charge pump setting (p62): 0x014 enable, 0x010 disable, 0.66 OLED 0x14*/ U8X8_C(0x040), /* set display start line to 0, 0.66 OLED */ U8X8_C(0x0a6), /* none inverted normal display mode */ U8X8_C(0x0a4), /* output ram to display */ U8X8_CA(0x020, 0x000), /* horizontal addressing mode */ U8X8_C(0x0a1), /* segment remap a0/a1, 0.66 OLED */ U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse, 0.66 OLED */ // Flipmode // U8X8_C(0x0a0), /* segment remap a0/a1*/ // U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */ U8X8_CA(0x0da, 0x012), /* com pin HW config, sequential com pin config (bit 4), disable left/right remap (bit 5), 0.66 OLED */ U8X8_CA(0x081, 0x0af), /* [2] set contrast control, 0.42 OLED */ U8X8_CA(0x0d9, 0x022), /* [2] pre-charge period 0x022/f1, 0.42 OLED datasheet: 0x22 */ U8X8_CA(0x0db, 0x020), /* vcomh deselect level, 0.42 OLED datasheet: 0x20 */ U8X8_C(0x02e), /* Deactivate scroll */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_ssd1306_72x40_powersave0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C(0x0af), /* display on */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_ssd1306_72x40_powersave1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C(0x0ae), /* display off */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_ssd1306_72x40_flip0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C(0x0a1), /* segment remap a0/a1*/ U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_ssd1306_72x40_flip1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C(0x0a0), /* segment remap a0/a1*/ U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static uint8_t u8x8_d_ssd1306_72x40_generic(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr) { uint8_t x, c; uint8_t *ptr; switch(msg) { /* handled by the calling function case U8X8_MSG_DISPLAY_SETUP_MEMORY: u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1306_72x40_display_info); break; case U8X8_MSG_DISPLAY_INIT: u8x8_d_helper_display_init(u8x8); u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_er_init_seq); break; */ case U8X8_MSG_DISPLAY_SET_POWER_SAVE: if ( arg_int == 0 ) u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_powersave0_seq); else u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_powersave1_seq); break; case U8X8_MSG_DISPLAY_SET_FLIP_MODE: if ( arg_int == 0 ) { u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_flip0_seq); u8x8->x_offset = u8x8->display_info->default_x_offset; } else { u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_flip1_seq); u8x8->x_offset = u8x8->display_info->flipmode_x_offset; } break; #ifdef U8X8_WITH_SET_CONTRAST case U8X8_MSG_DISPLAY_SET_CONTRAST: u8x8_cad_StartTransfer(u8x8); u8x8_cad_SendCmd(u8x8, 0x081 ); u8x8_cad_SendArg(u8x8, arg_int ); /* ssd1306 has range from 0 to 255 */ u8x8_cad_EndTransfer(u8x8); break; #endif case U8X8_MSG_DISPLAY_DRAW_TILE: u8x8_cad_StartTransfer(u8x8); x = ((u8x8_tile_t *)arg_ptr)->x_pos; x *= 8; x += u8x8->x_offset; u8x8_cad_SendCmd(u8x8, 0x010 | (x>>4) ); u8x8_cad_SendCmd(u8x8, 0x000 | ((x&15))); u8x8_cad_SendCmd(u8x8, 0x0b0 | (((u8x8_tile_t *)arg_ptr)->y_pos)); do { c = ((u8x8_tile_t *)arg_ptr)->cnt; ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr; u8x8_cad_SendData(u8x8, c*8, ptr); /* note: SendData can not handle more than 255 bytes */ arg_int--; } while( arg_int > 0 ); u8x8_cad_EndTransfer(u8x8); break; default: return 0; } return 1; } static const u8x8_display_info_t u8x8_ssd1306_72x40_display_info = { /* chip_enable_level = */ 0, /* chip_disable_level = */ 1, /* post_chip_enable_wait_ns = */ 20, /* pre_chip_disable_wait_ns = */ 10, /* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */ /* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */ /* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */ /* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */ /* sck_clock_hz = */ 8000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns, increased to 8MHz (issue 215) */ /* spi_mode = */ 0, /* active high, rising edge */ /* i2c_bus_clock_100kHz = */ 4, /* data_setup_time_ns = */ 40, /* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */ /* tile_width = */ 9, /* tile_height = */ 5, /* default_x_offset = */ 28, /* flipmode_x_offset = */ 28, /* pixel_width = */ 72, /* pixel_height = */ 40 }; /* EastRising 0.41 OLED https://www.buydisplay.com/default/white-0-42-inch-oled-display-panel-72x40-iic-i2c-serial-spi-ssd1306 */ uint8_t u8x8_d_ssd1306_72x40_er(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr) { if ( msg == U8X8_MSG_DISPLAY_SETUP_MEMORY ) { u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1306_72x40_display_info); return 1; } else if ( msg == U8X8_MSG_DISPLAY_INIT ) { u8x8_d_helper_display_init(u8x8); u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1306_72x40_er_init_seq); return 1; } return u8x8_d_ssd1306_72x40_generic(u8x8, msg, arg_int, arg_ptr); }