/* u8x8_d_st75160.c Universal 8bit Graphics Library (https://github.com/olikraus/u8g2/) Copyright (c) 2021, olikraus@gmail.com All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. REQUESTED IN https://github.com/olikraus/u8g2/issues/1642 STATUS 13 Aug 2022: NOT TESTED, MAY NOT WORK.. 0x030 ext 00 0x031 ext 01 0x038 ext 10 0x039 ext 11 cad 011 code examples: http://www.it610.com/article/2601023.htm normal mode: 0x00c bit format U8X8_CA( 0xbc, 0x00 ), data scan dir U8X8_A( 0xa6 ), y: 0 offset flip mode: 0x008 bit format U8X8_CA( 0xbc, 0x03 ), data scan dir U8X8_A( 0xa6 ), y: 5 offset */ #include "u8x8.h" /* not a real power down for the st75256... just a display off */ static const uint8_t u8x8_d_st75256_256x128_powersave0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x94 ), /* sleep out */ U8X8_DLY(10), U8X8_C( 0xaf ), /* display on */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_st75256_256x128_powersave1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0xae ), /* display off */ U8X8_C( 0x95 ), /* sleep in */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; /* marked as unused to avoid compiler warning, issue 1802 */ #ifdef NOT_USED static const uint8_t u8x8_d_st75256_jlx256128_flip0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x00 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x00c ), /* data format LSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_st75256_jlx256128_flip1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x03 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x008 ), /* data format MSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; #endif static const uint8_t u8x8_d_st75256_jlx172104_flip0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x02 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x00c ), /* data format LSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_st75256_jlx172104_flip1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x01 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x008 ), /* data format MSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; /* marked as unused to avoid compiler warning, issue 1802 */ #ifdef NOT_USED static const uint8_t u8x8_d_st75256_jlx256160_flip0_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x00 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x00c ), /* data format LSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; static const uint8_t u8x8_d_st75256_jlx256160_flip1_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x03 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x008 ), /* data format MSB top */ U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; #endif /*=============================================*/ /* JM16096 https://github.com/olikraus/u8g2/issues/1642 */ static const u8x8_display_info_t u8x8_st75160_jm16096_display_info = { /* chip_enable_level = */ 0, /* chip_disable_level = */ 1, /* post_chip_enable_wait_ns = */ 20, /* pre_chip_disable_wait_ns = */ 20, /* reset_pulse_width_ms = */ 5, /* post_reset_wait_ms = */ 5, /**/ /* sda_setup_time_ns = */ 20, /* */ /* sck_pulse_width_ns = */ 40, /* */ /* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */ /* spi_mode = */ 0, /* active high, rising edge */ /* i2c_bus_clock_100kHz = */ 4, /* 400KHz */ /* data_setup_time_ns = */ 15, /* write_pulse_width_ns = */ 70, /* tile_width = */ 20, /* tile_height = */ 12, /* default_x_offset = */ 0, /* x offset in flipmode 0 */ /* flipmode_x_offset = */ 0, /* */ /* pixel_width = */ 160, /* pixel_height = */ 96 }; static const uint8_t u8x8_d_st75160_jm16096_init_seq[] = { U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */ U8X8_DLY(20), U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x094 ), /* sleep out */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x0ae ), /* display off */ U8X8_C( 0x031 ), /* select 01 commands */ U8X8_CA( 0x0d7, 0x09f ), /* disable auto read */ //U8X8_C( 0x031 ), /* select 01 commands */ U8X8_C( 0x032 ), /* analog circuit set */ U8X8_A( 0x000 ), /* code example: OSC Frequency adjustment */ U8X8_A( 0x001 ), /* Frequency on booster capacitors 1 = 6KHz? */ U8X8_A( 0x004 ), /* Bias: 1: 1/13, 2: 1/12, 3: 1/11, 4:1/10, 5:1/9 */ //U8X8_C( 0x031 ), /* select 01 commands */ U8X8_C( 0x020 ), /* gray levels */ U8X8_A( 0x01 ), U8X8_A( 0x03 ), U8X8_A( 0x05 ), U8X8_A( 0x07 ), U8X8_A( 0x09), U8X8_A( 0x0b ), U8X8_A( 0x0d ), U8X8_A( 0x10 ), U8X8_A( 0x11 ), U8X8_A( 0x13 ), U8X8_A( 0x15 ), U8X8_A( 0x17 ), U8X8_A( 0x19 ), U8X8_A( 0x1b ), U8X8_A( 0x1d ), U8X8_A( 0x1f ), U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CAA(0x75, 0, 0x4f), /* row range */ U8X8_CAA(0x15, 0, 239), /* col range */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0xbc, 0x02 ), /* data scan dir */ U8X8_A( 0xa6 ), /* ??? */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0x00c ), /* data format LSB top */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_C( 0xca ), /* display control, 3 args follow */ U8X8_A( 0x00 ), /* 0x00: no clock division, 0x04: devide clock */ U8X8_A( 95 ), /* 1/96 duty */ U8X8_A( 0x20 ), /* nline off */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0x0f0, 0x010 ), /* monochrome mode = 0x010*/ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CAA( 0x81, 0x18, 0x04 ), /* Volume control */ //U8X8_C( 0x030 ), /* select 00 commands */ U8X8_CA( 0x020, 0x00b ), /* Power control: Regulator, follower & booster on */ U8X8_DLY(100), U8X8_END_TRANSFER(), /* disable chip */ U8X8_END() /* end of sequence */ }; uint8_t u8x8_d_st75160_jm16096(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr) { uint8_t x, c; uint8_t *ptr; switch(msg) { case U8X8_MSG_DISPLAY_DRAW_TILE: u8x8_cad_StartTransfer(u8x8); x = ((u8x8_tile_t *)arg_ptr)->x_pos; x *= 8; u8x8_cad_SendCmd(u8x8, 0x030 ); /* select command set */ u8x8_cad_SendCmd(u8x8, 0x075 ); /* row */ if ( u8x8->x_offset == 0 ) /* 0 means flip mode 1 */ u8x8_cad_SendArg(u8x8, 1+(((u8x8_tile_t *)arg_ptr)->y_pos)); else u8x8_cad_SendArg(u8x8, (((u8x8_tile_t *)arg_ptr)->y_pos)); u8x8_cad_SendArg(u8x8, 0x04f); //u8x8_cad_SendArg(u8x8, (((u8x8_tile_t *)arg_ptr)->y_pos)); u8x8_cad_SendCmd(u8x8, 0x015 ); /* col */ u8x8_cad_SendArg(u8x8, x+u8x8->x_offset); u8x8_cad_SendArg(u8x8, 255); u8x8_cad_SendCmd(u8x8, 0x05c ); do { c = ((u8x8_tile_t *)arg_ptr)->cnt; ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr; c *= 8; if ( c + x > 160u ) { c = 160u; c -= x; } u8x8_cad_SendData(u8x8, c, ptr); x += c; arg_int--; } while( arg_int > 0 ); u8x8_cad_EndTransfer(u8x8); return 1; case U8X8_MSG_DISPLAY_SETUP_MEMORY: //u8x8_SetI2CAddress(u8x8, 0x078); /* lowest I2C adr of the ST75256 */ u8x8_d_helper_display_setup_memory(u8x8, &u8x8_st75160_jm16096_display_info); return 1; case U8X8_MSG_DISPLAY_INIT: u8x8_d_helper_display_init(u8x8); u8x8_cad_SendSequence(u8x8, u8x8_d_st75160_jm16096_init_seq); return 1; case U8X8_MSG_DISPLAY_SET_POWER_SAVE: if ( arg_int == 0 ) u8x8_cad_SendSequence(u8x8, u8x8_d_st75256_256x128_powersave0_seq); else u8x8_cad_SendSequence(u8x8, u8x8_d_st75256_256x128_powersave1_seq); return 1; case U8X8_MSG_DISPLAY_SET_FLIP_MODE: if ( arg_int == 0 ) { u8x8_cad_SendSequence(u8x8, u8x8_d_st75256_jlx172104_flip0_seq); u8x8->x_offset = u8x8->display_info->default_x_offset; } else { u8x8_cad_SendSequence(u8x8, u8x8_d_st75256_jlx172104_flip1_seq); u8x8->x_offset = u8x8->display_info->flipmode_x_offset; } return 1; #ifdef U8X8_WITH_SET_CONTRAST case U8X8_MSG_DISPLAY_SET_CONTRAST: u8x8_cad_StartTransfer(u8x8); u8x8_cad_SendCmd(u8x8, 0x030 ); u8x8_cad_SendCmd(u8x8, 0x081 ); /* there are 9 bit for the volume control */ u8x8_cad_SendArg(u8x8, (arg_int & 0x1f)<<1 ); /* lower 6 bit */ u8x8_cad_SendArg(u8x8, (arg_int>>5)); /* upper 3 bit */ u8x8_cad_EndTransfer(u8x8); return 1; #endif } return 0; }